World Library  
Flag as Inappropriate
Email this Article

Microstrip

Article Id: WHEBN0002022356
Reproduction Date:

Title: Microstrip  
Author: World Heritage Encyclopedia
Language: English
Subject: Metamaterial antenna, Microstrip antenna, Transmission line, Printed circuit board, Waveguide filter
Collection: Electronics, Microwave Technology, Printed Circuit Board Manufacturing, Signal Cables
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Microstrip

Cross-section of microstrip geometry. Conductor (A) is separated from ground plane (D) by dielectric substrate (C). Upper dielectric (B) is typically air.
Microstrip is a type of electrical transmission line which can be fabricated using printed circuit board technology, and is used to convey microwave-frequency signals. It consists of a conducting strip separated from a ground plane by a dielectric layer known as the substrate. Microwave components such as antennas, couplers, filters, power dividers etc. can be formed from microstrip, the entire device existing as the pattern of metallization on the substrate. Microstrip is thus much less expensive than traditional waveguide technology, as well as being far lighter and more compact. Microstrip was developed by ITT laboratories as a competitor to stripline (first published by Grieg and Engelmann in the December 1952 IRE proceedings[1]).

The disadvantages of microstrip compared with waveguide are the generally lower power handling capacity, and higher losses. Also, unlike waveguide, microstrip is not enclosed, and is therefore susceptible to cross-talk and unintentional radiation.

For lowest cost, microstrip devices may be built on an ordinary FR-4 (standard PCB) substrate. However it is often found that the dielectric losses in FR4 are too high at microwave frequencies, and that the dielectric constant is not sufficiently tightly controlled. For these reasons, an alumina substrate is commonly used.

On a smaller scale, microstrip transmission lines are also built into monolithic microwave integrated circuits.

Microstrip lines are also used in high-speed digital PCB designs, where signals need to be routed from one part of the assembly to another with minimal distortion, and avoiding high cross-talk and radiation.

Microstrip is very similar to stripline and coplanar waveguide, and it is possible to integrate all three on the same substrate.

Contents

  • Inhomogeneity 1
  • Characteristic impedance 2
  • Bends 3
  • See also 4
  • References 5
  • External links 6

Inhomogeneity

The electromagnetic wave carried by a microstrip line exists partly in the dielectric substrate, and partly in the air above it. In general, the dielectric constant of the substrate will be different (and greater) than that of the air, so that the wave is travelling in an inhomogeneous medium. In consequence, the propagation velocity is somewhere between the speed of radio waves in the substrate, and the speed of radio waves in air. This behaviour is commonly described by stating the effective dielectric constant (or effective relative permittivity) of the microstrip; this being the dielectric constant of an equivalent homogeneous medium (i.e., one resulting in the same propagation velocity).

Further consequences of an inhomogeneous medium include:

  • The line will not support a true TEM wave; at non-zero frequencies, both the E and H fields will have longitudinal components (a hybrid mode).[2] The longitudinal components are small however, and so the dominant mode is referred to as quasi-TEM.
  • The line is dispersive. With increasing frequency, the effective dielectric constant gradually climbs towards that of the substrate, so that the phase velocity gradually decreases.[2][3] This is true even with a non-dispersive substrate material (the substrate dielectric constant will usually fall with increasing frequency).
  • The characteristic impedance of the line changes slightly with frequency (again, even with a non-dispersive substrate material). The characteristic impedance of non-TEM modes is not uniquely defined, and depending on the precise definition used, the impedance of microstrip either rises, falls, or falls then rises with increasing frequency.[4] The low-frequency limit of the characteristic impedance is referred to as the quasi-static characteristic impedance, and is the same for all definitions of characteristic impedance.
  • The wave impedance varies over the cross-section of the line.

Characteristic impedance

A closed-form approximate expression for the quasi-static characteristic impedance of a microstrip line was developed by Wheeler:[5][6][7]

Z_\textrm{microstrip} = \frac{Z_{0}}{2 \pi \sqrt{2 (1 + \varepsilon_{r})}} \mathrm{ln}\left( 1 + \frac{4 h}{w_\textrm{eff}} \left( \frac{14 + \frac{8}{\varepsilon_{r}}}{11} \frac{4 h}{w_\textrm{eff}} + \sqrt{\left( \frac{14 + \frac{8}{\varepsilon_{r}}}{11} \frac{4 h}{w_\textrm{eff}}\right)^{2} + \pi^{2} \frac{1 + \frac{1}{\varepsilon_{r}}}{2}}\right)\right),

where w_\mathrm{eff} is the effective width, which is the actual width of the strip, plus a correction to account for the non-zero thickness of the metallization:

w_\textrm{eff} = w + t \frac{1 + \frac{1}{\varepsilon_{r}}}{2 \pi} \mathrm{ln}\left( \frac{4 e}{\sqrt{\left( \frac{t}{h}\right)^{2} + \left( \frac{1}{\pi} \frac{1}{\frac{w}{t} + \frac{11}{10}}\right)^{2}}}\right).

Here Z0 is the impedance of free space, εr is the relative permittivity of substrate, w is the width of the strip, h is the thickness ("height") of substrate, and t is the thickness of the strip metallization.

This formula is asymptotic to an exact solution in three different cases

  1. w \gg h, any \varepsilon_{r} (parallel plate transmission line),
  2. w \ll h, \varepsilon_{r} = 1 (wire above a ground-plane) and
  3. w \ll h, \varepsilon_{r} \gg 1.

It is claimed that for most other cases, the error in impedance is less than 1%, and is always less than 2%.[7] By covering all aspect-ratios in one formula, Wheeler 1977 improves on Wheeler 1965[6] which gives one formula for w / h > 3.3 and another for w / h \le 3.3 (thus introducing a discontinuity in the result at w / h = 3.3). Nevertheless, the 1965 paper is perhaps the more often cited. A number of other approximate formulae for the characteristic impedance have been advanced by other authors. However, most of these are applicable to only a limited range of aspect-ratios, or else cover the entire range piecewise.

Curiously, Harold Wheeler disliked both the terms 'microstrip' and 'characteristic impedance', and avoided using them in his papers.

Bends

In order to build a complete circuit in microstrip, it is often necessary for the path of a strip to turn through a large angle. An abrupt 90° bend in a microstrip will cause a significant portion of the signal on the strip to be reflected back towards its source, with only part of the signal transmitted on around the bend. One means of effecting a low-reflection bend, is to curve the path of the strip in an arc of radius at least 3 times the strip-width.[8] However, a far more common technique, and one which consumes a smaller area of substrate, is to use a mitred bend.

Microstrip 90° mitred bend. The percentage mitre is 100x/d
To a first approximation, an abrupt un-mitred bend behaves as a shunt capacitance placed between the ground plane and the bend in the strip. Mitring the bend reduces the area of metallization, and so removes the excess capacitance. The percentage mitre is the cut-away fraction of the diagonal between the inner and outer corners of the un-mitred bend.

The optimum mitre for a wide range of microstrip geometries has been determined experimentally by Douville and James.[9] They find that a good fit for the optimum percentage mitre is given by

M = 100 \frac{x}{d} \% = (52 + 65 e^{- \frac{27}{20} \frac{w}{h}}) \%

subject to w/h \ge 0.25 and with the substrate dielectric constant \varepsilon_{r} \le 25. This formula is entirely independent of \varepsilon_{r}. The actual range of parameters for which Douville and James present evidence is 0.25 \le w/h \le 2.75 and 2.5 \le \varepsilon_{r} \le 25. They report a VSWR of better than 1.1 (i.e., a return better than −26 dB) for any percentage mitre within 4% (of the original d) of that given by the formula. At the minimum w/h of 0.25, the percentage mitre is 98.4%, so that the strip is very nearly cut through.

For both the curved and mitred bends, the electrical length is somewhat shorter than the physical path-length of the strip.

See also

References

  1. ^ Grieg, D. D.; Engelmann, H. F. (Dec 1952). "Microstrip-A New Transmission Technique for the Klilomegacycle Range". Proceedings of the IRE 40 (12): 1644–1650.  
  2. ^ a b Denlinger, E. J. (January 1971). "A frequency dependent solution for microstrip transmission lines". IEEE Trans. Microwave Theory Tech. MTT-19: 30–39. 
  3. ^ Cory, H. (January 1981). "Dispersion characteristics of microstrip lines". IEEE Trans. Microwave Theory Tech. MTT-29: 59–61. 
  4. ^ Bianco, B.; Panini, L.; Parodi, M.; Ridetlaj, S. (March 1978). "Some considerations about the frequency dependence of the characteristic impedance of uniform microstrips". IEEE Trans. Microwave Theory Tech. MTT-26: 182–185. 
  5. ^  
  6. ^ a b  
  7. ^ a b  
  8. ^ Lee, T. H. (2004). Planar Microwave Engineering. Cambridge University Press. pp. 173–174. 
  9. ^ Douville, R. J. P.; James, D. S. (March 1978). "Experimental study of symmetric microstrip bends and their compensation". IEEE Trans. Microwave Theory Tech. MTT-26: 175–182. 

External links

  • Microstrip in Microwave Encyclopedia
  • Microstrip Analysis/Synthesis Calculator
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.