World Library  
Flag as Inappropriate
Email this Article

Distance measuring equipment

 

Distance measuring equipment

D-VOR/DME ground station
DME antenna beside the DME Transponder shelter

Distance measuring equipment (DME) is a transponder-based radio navigation technology that measures slant range distance by timing the propagation delay of VHF or UHF radio signals.

Developed in Australia, it was invented by James Gerry Gerrand [1] under the supervision of Amalgamated Wireless Australasia Limited in the early 1950s operating in the 200 MHz VHF band. This Australian domestic version was referred to by the Federal Department of Civil Aviation as DME(D) (or DME Domestic), and the later international version adopted by ICAO as DME(I).

DME is similar to secondary radar, except in reverse. The system was a post-war development of the IFF (identification friend or foe) systems of World War II. To maintain compatibility, DME is functionally identical to the distance measuring component of TACAN.

Contents

  • Operation 1
  • Hardware 2
  • Timing 3
  • Distance calculation 4
  • Accuracy 5
  • Specification 6
  • Radio frequency and modulation data 7
  • Terminal DME 8
  • Future 9
  • See also 10
  • References 11
  • External links 12

Operation

Aircraft use DME to determine their distance from a land-based transponder by sending and receiving pulse pairs – two pulses of fixed duration and separation. The ground stations are typically co-located with VORs. A typical DME ground transponder system for en-route or terminal navigation will have a 1 kW peak pulse output on the assigned UHF channel.

A low-power DME can be co-located with an ILS glide slope antenna installation where it provides an accurate distance to touchdown function, similar to that otherwise provided by ILS marker beacons.

Hardware

The DME system is composed of a VHF transmitter/receiver (interrogator) in the aircraft and a VHF receiver/transmitter (transponder) on the ground.

DME distance and VOR/ADF cockpit display instruments

Timing

SEARCH MODE: 150 interrogation pulse-pairs per second.

The aircraft interrogates the ground transponder with a series of pulse-pairs (interrogations) and, after a precise time delay (typically 50 microseconds), the ground station replies with an identical sequence of pulse-pairs. The DME receiver in the aircraft searches for reply pulse-pairs (X-mode= 12 microsecond spacing) with the correct interval and reply pattern to its original interrogation pattern. (Pulses-pairs that are not coincident with the individual aircraft's interrogation pattern e.g. not synchronous, are referred to as filler pulse-pairs, or Squitter. Also, replies to other aircraft that are therefore non-synchronous also appear as squitter).

TRACK MODE: less than 30 interrogation Pulse-pairs per second, as the average amount of pulses in SEARCH and TRACK is limited to max 30 Pulse Pairs per second.

The aircraft interrogator locks on to the DME ground station once it recognizes a particular reply pulse sequence has the same spacing as the original interrogation sequence. Once the receiver is locked on, it has a narrower window in which to look for the echoes and can retain lock.

Distance calculation

A radio signal takes approximately 12.36 microseconds to travel 1 nautical mile (1,852 m) to the target and back—also referred to as a radar-mile. The time difference between interrogation and reply, minus the 50 microsecond ground transponder delay, is measured by the interrogator's timing circuitry and converted to a distance measurement (slant range), in nautical miles, then displayed on the cockpit DME display.

The distance formula, distance = rate * time, is used by the DME receiver to calculate its distance from the DME ground station. The rate in the calculation is the velocity of the radio pulse, which is the speed of light (roughly 300,000,000 m/s or 186,000 mi/s). The time in the calculation is (total time – 50µs)/2.

Accuracy

The accuracy of DME ground stations is 185 m (±0.1 nmi).[2] It's important to understand that DME provides the physical distance from the aircraft to the DME transponder. This distance is often referred to as 'slant range' and depends trigonometrically upon both the altitude above the transponder and the ground distance from it.

For example, an aircraft directly above the DME station at 6,076 ft (1 nmi) altitude would still show 1.0 nmi (1.9 km) on the DME readout. The aircraft is technically a mile away, just a mile straight up. Slant range error is most pronounced at high altitudes when close to the DME station.

Radio-navigation aids must keep a certain degree of accuracy, given by international standards, FAA,[3] ICAO, etc. To assure this is the case, flight inspection organizations check periodically critical parameters with properly equipped aircraft to calibrate and certify DME precision.

ICAO recommends accuracy of less than the sum of 0.25 nmi plus 1.25% of the distance measured.

Specification

A typical DME transponder can provide distance information to 100 to 200 aircraft at a time. Above this limit the transponder avoids overload by limiting the sensitivity of the receiver. Replies to weaker more distant interrogations are ignored to lower the transponder load.

Radio frequency and modulation data

DME frequencies are paired to VHF omnidirectional range (VOR) frequencies and a DME interrogator is designed to automatically tune to the corresponding DME frequency when the associated VOR frequency is selected. An airplane’s DME interrogator uses frequencies from 1,025 to 1,150 MHz. DME transponders transmit on a channel in the 962 to 1,213 MHz range and receive on a corresponding channel between 1,025 to 1,150 MHz. The band is divided into 126 channels for interrogation and 126 channels for reply. The interrogation and reply frequencies always differ by 63 MHz. The spacing of all channels is 1 MHz with a signal spectrum width of 100 kHz.

Technical references to X and Y channels relate only to the spacing of the individual pulses in the DME pulse pair, 12 microsecond spacing for X channels and 30 microsecond spacing for Y channels.

DME facilities identify themselves with a 1,350 Hz morse code three letter identity. If collocated with a VOR or ILS, it will have the same identity code as the parent facility. Additionally, the DME will identify itself between those of the parent facility. The DME identity is 1,350 Hz to differentiate itself from the 1,020 Hz tone of the VOR or the ILS localizer.

Terminal DME

A terminal DME, referred to as a TDME in navigational charts, is a DME that is designed to provide a 0 reading at the threshold point of the runway, regardless of the physical location of the equipment. It is typically associated with ILS or other instrument approach.

Future

DME operation will continue and possibly expand as an alternate navigation source to space-based navigational systems such as GPS and Galileo.[4]

See also

References

  1. ^ http://www.smh.com.au/national/obituaries/engineer-exploded-myths-in-many-fields-20130108-2cell.html
  2. ^ Department of Defense and Department of Transportation (December 2001). "2001 Federal Radionavigation Systems" (PDF). Retrieved 5 July 2011. 
  3. ^ Federal Aviation Administration (2 September 1982). "U.S. National Aviation Standard for the VOR/DME/TACAN Systems". 
  4. ^ Department of Defense, Department of Homeland Security and Department of Transportation (January 2009). "2008 Federal Radionavigation Plan" (PDF). Retrieved 8 September 2010. 

External links

  • DME Basics
  • UK Navaids Gallery with detailed Technical Descriptions of their operation
  • Flash based instrument simulator with DME
  • U.S. National Aviation Handbook for the VOR/DME/TACAN Systems
  • ICAO Annex 10 Volume 1 International Standards & Recommended Practices
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.