World Library  
Flag as Inappropriate
Email this Article

Filter capacitor

Article Id: WHEBN0002304203
Reproduction Date:

Title: Filter capacitor  
Author: World Heritage Encyclopedia
Language: English
Subject: Bleeder resistor, Vienna rectifier, Glitch removal, Power supply unit (computer), Datasheet
Collection: Capacitors
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Filter capacitor

Filter capacitors are capacitors used for filtering of undesirable frequencies. They are common in electrical and electronic equipment, and cover a number of applications, such as:

Filter capacitors are not the same as reservoir capacitors, the tasks the two perform are different, albeit related.

Contents

  • Types 1
    • High-pass and low-pass filters 1.1
    • Power rail filtering 1.2
    • Radio frequency work 1.3
      • Ultra High Frequency-UHF 1.3.1
      • Microwave 1.3.2
    • Computer power rail filtering 1.4
    • Lowest cost 1.5
    • Mains filtering 1.6
    • Contact suppression 1.7

Types

Many filtering tasks have specific types of capacitor that are required or typically used for the task.

High-pass and low-pass filters

Power rail filtering

Electrolytic capacitors are usually used due to high capacity at low cost and low size. Smaller non-electrolytics may be paralleled with these to compensate for electrolytics' poor performance at high frequencies.

Radio frequency work

Ceramic plate capacitors are usually favoured due to extremely low inductance and low cost. Where precision is needed, silver mica capacitors offer superior precision and stability. Where manual tunability is required, plastic film trimmers are sometimes used, though it has long been more popular to adjust the inductor to achieve tuning.

Ultra High Frequency-UHF

Disc and plate ceramic capacitors are used due to particularly low inductance. Often a ceramic disc sits in a notch cut in the PCB, with the tracks soldered directly to the disc for best performance.

Microwave

At microwave frequencies, the (FR4) Printed circuit board (PCB) material acts as a capacitor, and the PCB track has inherent inductance. The net result depends on the ratio of capacitance and inductance present.

Increasing PCB track width causes additional capacitance, and thus a net capacitance. Narrowing track width reduces capacitance, produces a net inductance.

Computer power rail filtering

Computers use large numbers of filter capacitors, making size an important factor. Solid tantalum and wet tantalum capacitors offer some of the best CV (capacitance/voltage) performance in some of the most volumetrically efficient packaging available. High currents and low voltages also make low equivalent series resistance (ESR) important. Solid tantalum capacitors offer low ESR versions that can often meet ESR requirements but they are not the lowest ESR option among all capacitors. Solid tantalums have an additional issue which must be addressed during the design stage. Solid tantalum capacitors must be voltage derated in all applications. A 50% voltage derating is recommended and generally accepted as the industry standard; e.g.: A 50V solid tantalum capacitor should never be exposed to an actual application voltage above 25V. Solid tantalum capacitors are very reliable components if the proper care is taken and all design guidelines are carefully followed. Unfortunately, the failure mechanism for a solid tantalum capacitor is a short which will result in a violent flaring up and smoking on a PCB capable of damaging other components in close proximity as well as completely destroying the capacitor. Fortunately, most solid tantalum capacitor failures will be immediate and very evident. Once in application solid tantalum capacitor performance will improve over time and the chances of a failure due to component mis-manufacturing decrease. Wet tantalums are a type of the electrolytic capacitor, using a tantalum pellet in an electrolytic material sealed in a hermetic package. This type of tantalum capacitor does not require the same derating that a solid tantalum does and its failure mechanism is open. A 10% to 20% voltage derating curve is recommended for wet tantalums when operating from 85C to 125C. Wet tantalums are not commonly referred to as just 'electrolytics' because usually 'electrolytic' refers to aluminium electrolytics.

Lowest cost

Ceramic (for values <0.47 micro-farad-µF) and electrolytic (for 0.47 µF and up) are normally the preferred types where their performance is sufficient, since these are the lowest cost types of capacitors. Hence they are very popular in filters of many types.

Mains filtering

Mains filter capacitors are usually encapsulated wound plastic film types, since these deliver high voltage rating at low cost, and may be made self healing and fusible. Mains filter capacitors are often ceramic RFI/EMI suppression capacitors. The additional safety requirements for mains filtering are:

  • Line to neutral capacitors are flame retardant, and in Europe are required to use class X dielectrics
  • Line or neutral to earth: Must be flame retardant; also, the dielectric must be self healing and fusible. In Europe these are class Y capacitors.

Contact suppression

A wound plastic film mains rated capacitor plus series resistor are incorporated into a single component envelope for

This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.