World Library  
Flag as Inappropriate
Email this Article

Marking out

Article Id: WHEBN0001925023
Reproduction Date:

Title: Marking out  
Author: World Heritage Encyclopedia
Language: English
Subject: Marking blue, Marking gauge, Engineer's blue, Punch (tool), Calipers
Collection: Metalworking Measuring Instruments, Woodworking
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Marking out

Marking out or layout is the process of transferring a design or pattern to a work piece, as the first step in the manufacturing process.[1] It is performed in many industries or hobbies although in the repetition industries the machine's initial setup is designed to remove the need to mark out every individual piece.

Contents

  • Manufacturing 1
  • Welding 2
  • Woodworking 3
  • References 4

Manufacturing

Marking out consists of transferring the dimensions from the plan to the work piece in preparation for the next step, machining or manufacture.

Typical tools include:[2]

  • Surface plate or marking out table — provides a true surface from which to work
  • Angle plates — assist in holding the workpiece perpendicular to the table
  • Scriber — is the equivalent of a pen or pencil. It literally scratches the metal surface leaving behind a fine, bright line
  • Height gauge or scribing block — allows lines to be scribed at a preset distance, from the tables surface
  • Surface gage — an ungraduated comparison measuring tool that performs much the same function as the vernier height gage. It is often used in conjunction with a dial indicator and a precision height gage.
  • Marking blue — to provide a usable writing surface by covering any existing scratches and providing a contrasting background
  • Profile gauge
  • Protractor — to assist in the transfer of angular measurements
  • Combination square — an alternative tool for transferring angular measurements
  • Square — to transfer 90° angles to the workpiece
  • Punches — either prick or punch (engineering) punch to create permanent marks or dimples for drill bits to start in
    • Automatic center punch — a spring-loaded punch that creates prick punch marks without the need for a ball peen hammer
  • Ball peen hammer — used in conjunction with the punches to provide the striking blow needed
  • Dividers or measuring compass — used for marking out circles of any desired radius,

Welding

As welding does not always require the use of fine tolerances, marking out is usually performed by using centre punches, hammers, tape measures and chalk.

The "chalk" is actually a small pre-cut block of talc (soapstone). These talc blocks can be sharpened to a stronger point than the softer blackboard chalk. The color of the chalk provides good contrast against the dark color of the hot rolled steel that is generally used.[3]

Woodworking

In carpentry and joinery practice a pencil is used for marking while in cabinetmaking a marking knife provides for greater accuracy. A storey pole is used to lay out repeated measurements such as the location of joints in timber framing, courses of siding such as wood shingles and clapboards, the heights of doorjambs and the courses of bricks in masonry.[4] Carpenters typically mark out framing members on-center, the measurements are to the centers of each member.

References

  1. ^ Brett, Peter (2005). Carpentry & Joinery: Job Knowledge. Carpentry & Joinery 1 (Illustrated, 3rd ed.). Nelson Thornes.  
  2. ^ Caborn, Colin; Cave, John (2000). Design and Technology (Revised, Illustrated, 3rd ed.). Nelson Thornes. Ch. 12, Part 1.  
  3. ^ Timings, Roger (2012). Fabrication and Welding Engineering. Routledge. Ch. 5.8.  
  4. ^ Frane, James T.. Craftsman's illustrated dictionary of construction terms. Carlsbad, CA: Craftsman Book Co., 1994. 339.
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.