Single-carrier frequency-division-multiplex

Single-carrier FDMA (SC-FDMA) is a frequency-division multiple access scheme. Like other multiple access schemes (TDMA, FDMA, CDMA, OFDMA), it deals with the assignment of multiple users to a shared communication resource. SC-FDMA can be interpreted as a linearly precoded OFDMA scheme, in the sense that it has an additional DFT processing preceding the conventional OFDMA processing.

SC-FDMA has drawn great attention as an attractive alternative to OFDMA, especially in the uplink communications where lower peak-to-average power ratio (PAPR) greatly benefits the mobile terminal in terms of transmit power efficiency and reduced cost of the power amplifier. It has been adopted as the uplink multiple access scheme in 3GPP Long Term Evolution (LTE), or Evolved UTRA (E-UTRA).[1][2][3]

The performance of SC-FDMA, in relation to OFDMA has been the subject of various studies.[4][5][6] Although the performance gap is not much, SC-FDMA's additional advantage of low PAPR makes it a favorite especially for uplink wireless transmission in future mobile communication systems where transmitter power efficiency is of paramount importance.

Transmitter and Receiver Structure of LP-OFDMA/SC-FDMA

The process transmission of SC-FDMA scheme is very similar to OFDMA. For each user the sequence of bits transmitted is mapped in a complex constellation symbols (BPSK, QPSK or M-QAM). This different transmitters (users) are assigned different Fourier coefficients. This assignment is carried out in the mapping and demapping blocks. The receiver side includes one demapping block, one IDFT block and one detection block for each user signal to be received. Just like in OFDM, guard intervals (or called cyclic prefix) with cyclic repetition are introduced between blocks of symbols in view to efficiently eliminate time spreading (caused by multi-path propagation) among the blocks.

In SC-FDMA, multiple access among users is made possible by assigning different users, different sets of non-overlapping fourier-coefficients (sub-carriers). This is achieved at the transmitter by inserting (prior to IFFT) silent fourier-coefficients (at positions assigned to other users), and removing them on the receiver side after the FFT.


The distinguishing feature of SC-FDMA is that it leads to a single-carrier transmit signal, in contrast to OFDMA which is a multi-carrier transmission scheme. Subcarrier mapping can be classified into two types: localized mapping and distributed mapping.

In localized mapping, the DFT outputs are mapped to a subset of consecutive subcarriers thereby confining them to only a fraction of the system bandwidth. In distributed mapping, the DFT outputs of the input data are assigned to subcarriers over the entire bandwidth non-continuously, resulting in zero amplitude for the remaining subcarriers. A special case of distributed SC-FDMA is called interleaved SC-FDMA (IFDMA), where the occupied subcarriers are equally spaced over the entire bandwidth.[7]

Owing to its inherent single carrier structure, a prominent advantage of SC-FDMA over OFDM and OFDMA is that its transmit signal has a lower peak-to-average power ratio (PAPR); resulting in relaxed design parameters in the transmit path of a subscriber unit. Intuitively, the reasoning lies in the fact that while in OFDM the transmit symbols directly modulate the multiple sub-carriers, in SC-FDMA the transmit symbols are first preprocessed by a N-point DFT block.[8]

In OFDM as well as SC-FDMA, equalization is achieved on the receiver side after the FFT calculation, by multiplying each Fourier coefficient by a complex number. Thus, frequency-selective fading and phase distortion can be easily combated. The advantage is that FFT and frequency domain equalization requires less computation power than the conventional time-domain equalization.

A related concept is the combination of a single carrier transmission with the single-carrier frequency-domain-equalization (SC-FDE) scheme. [9] The single carrier transmission, unlike SC-FDMA and OFDM employ no IFFT or FFT at transmitter, but introduce the cyclic prefix to transform the linear channel convolution into a circular one. After removing the cyclic prefix at receiver, an FFT is applied to arrive in the frequency domain, where a simple single-carrier frequency-domain-equalization (SC-FDE) scheme can be employed, followed by the IFFT operation.

Useful properties

  1. Low PAPR (Crest Factor)
  2. Low sensitivity to carrier frequency offset
  3. Less sensitive to non linear distortion and hence, it allows the use of low-cost power amplifiers
  4. Greater robustness against spectra nulls

See also

  • 3GPP Long Term Evolution
  • OFDMA

References

This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.