World Library  
Flag as Inappropriate
Email this Article

Slag (welding)

Article Id: WHEBN0041394056
Reproduction Date:

Title: Slag (welding)  
Author: World Heritage Encyclopedia
Language: English
Subject: Arc welding, Welding
Collection: Arc Welding
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Slag (welding)

Examples of arc weld slag

Welding slag is a form of slag, or vitreous material produced as a byproduct of some arc welding processes, most specifically shielded metal arc welding (also known as stick welding), submerged arc welding, and flux-cored arc welding. Slag is formed when flux, the solid shielding material used in the welding process, melts in or on top of the weld zone. Slag is the solidified remaining flux after the weld area cools.[1]

Contents

  • Flux 1
    • Inclusions 1.1
  • Processes 2
    • Shielded metal arc welding 2.1
    • Flux-core arc welding 2.2
    • Submerged arc welding 2.3
    • Electroslag welding 2.4
  • Removal of slag 3
  • See also 4
  • References 5

Flux

Shielded metal arc welding process, showing slag

Welding flux is a combination of carbonate and silicate materials used in welding processes to shield the weld from atmospheric gases. When the heat of the weld zone reaches the flux, the flux melts and outgasses. The gases produced push the atmospheric gas back, preventing oxidation (and reactions with nitrogen).

The melted flux covers the molten metal in the weld zone. Flux materials are chosen so that the density of the melted flux / slag is lower than that of the metal being welded, so that the flux floats to the top of the weld puddle and leaves pure or nearly pure metal to solidify below.

Flux materials may also contribute to metal behavior in the molten metal, with physical or chemical alterations to the molten metal.

The flux cover also helps thermally insulate the weld and reduce the cooling rate.

Flux-core arc welding process, showing slag

Inclusions

Submerged arc welding process, showing slag

It is possible for areas of slag to become embedded within the solidified metal, if it did not float to the top of the molten metal for some reason. These are called inclusions and are a form of welding defect. Inclusions may be visible on the surface after cleaning, or may be completely contained within the metal, requiring grinding or drilling to remove (followed by re-welding that section).

Processes

Electroslag welding process, showing slag

Four welding processes use flux in slag-producing manners:

  • Shielded metal arc welding, also known as SMAW
  • Flux-core arc welding, also known as FCAW or FC
  • Submerged arc welding
  • Electroslag welding

Shielded metal arc welding

Flux-core arc welding

Submerged arc welding

Electroslag welding

Removal of slag

Slag does not contribute to strength or protection of metals after the welding process; it is waste material. Removal of the slag is necessary for four reasons:

  • ability to inspect the quality of the weld area;
  • aesthetics, or visual appearance;
  • if a second layer or pass of welding is to be made on top of the first;
  • to clean and clear the surface for coatings such as paint or oil.

Removal is usually done using manual or power tools. Manual tools may include a welding or chipping hammer, which has a pointed tip on one end to break up large chunks of slag efficiently, or wire brushes. Power tools include angle grinders with grinder disks or wire brush wheels.

See also

References

  1. ^ Modern Welding Technology (6th Edition), Howard B. Cary& Scott Helzer, 2004, ISBN 978-0131130296
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.