World Library  
Flag as Inappropriate
Email this Article

Bandgap voltage reference

Article Id: WHEBN0000516067
Reproduction Date:

Title: Bandgap voltage reference  
Author: World Heritage Encyclopedia
Language: English
Subject: Brokaw bandgap reference, Electronic circuits, Bipolar junction transistor
Publisher: World Heritage Encyclopedia

Bandgap voltage reference

A bandgap voltage reference is a temperature independent voltage reference circuit widely used in integrated circuits. It produces a fixed (constant) voltage irrespective of power supply variations, temperature changes and the loading on the device. Usually it has an output voltage around 1.25 V, close to the theoretical 1.22 eV bandgap of silicon at 0 K. This circuit concept was first published by David Hilbiber in 1964.[1] Bob Widlar,[2] Paul Brokaw[3] and others[4] followed up with other commercially successful versions.


Characteristic and balance point of T1 and T2

The voltage difference between two p-n junctions (e.g. diodes), operated at different current densities, is used to generate a proportional to absolute temperature (PTAT) current in a first resistor. This current is used to generate a voltage in a second resistor. This voltage in turn is added to the voltage of one of the junctions (or a third one, in some implementations). The voltage across a diode operated at constant current, or here with a PTAT current, is complementary to absolute temperature (CTAT—reduces with increasing temperature), with approx. −2 mV/K. If the ratio between the first and second resistor is chosen properly, the first order effects of the temperature dependency of the diode and the PTAT current will cancel out. The resulting voltage is about 1.2–1.3 V, depending on the particular technology and circuit design, and is close to the theoretical 1.22 eV bandgap of silicon at 0 K. The remaining voltage change over the operating temperature of typical integrated circuits is on the order of a few millivolts. This temperature dependency has a typical parabolic residual behavior since the linear (first order) effects are chosen to cancel.

Because the output voltage is by definition fixed around 1.25 V for typical bandgap reference circuits, the minimum operating voltage is about 1.4 V, as in a CMOS circuit at least one drain-source voltage of a FET (field effect transistor) has to be added. Therefore, recent work concentrates on finding alternative solutions, in which for example currents are summed instead of voltages, resulting in a lower theoretical limit for the operating voltage (Banba, 1999).

Note that sometimes confusion arises when using the abbreviation CTAT, where the "C" is incorrectly taken to mean "constant" rather than "complementary". To avoid this confusion, although not in widespread use, the term constant with temperature (CWT) is sometimes used.

When summing a PTAT (Proportional to Absolute Temperature) and a CTAT (Complementary to Absolute Temperature) current, only the linear terms of current are compensated, while the higher-order terms are limiting the TD (Temperature Drift) of the BGR at around 20ppm/oC, over a temperature range of 100 oC. For this reason, in 2001, Malcovati [5] designed a circuit topology that can compensate high-order non-linearities, thus achieving an improved TD. This design used an improved version of Banba [4] topology and an analysis of base-emitter temperature effects that was performed by Tsividis in 1980.[6] In 2012, Andreou [7] [8] has further improved the high-order non-linear compensation by using a second opamp along with an additional resistor leg at the point where the two currents are summed up. This method enhanced further the curvature correction and achieved superior TD performance over a wider temperature range. In addition it achieved improved Line Regulation and lower Noise.


  • 1966, US Patent 3271660, Reference voltage source, David Hilbiber.[9]
  • 1971, US Patent 3617859, Electrical regulator apparatus including a zero temperature coefficient voltage reference circuit, Robert Dobkin and Robert Widlar.[10]
  • 1981, US Patent 4249122, Temperature compensated bandgap IC voltage references, Robert Widlar.[11]
  • 1984, US Patent 4447784, Temperature compensated bandgap voltage reference circuit, Robert Dobkin.[12]

See also


  1. ^ Hilbiber, D.F. (1964), "A new semiconductor voltage standard", 1964 International Solid-State Circuits Conference: Digest of Technical Papers 2: 32–33,  
  2. ^  
  3. ^  
  4. ^ a b Banba, H.; Shiga, H.; Umezawa, A.; Miyaba, T.; Tanzawa, T.; Atsumi, S.; Sakui, K. (May 1999), "A CMOS bandgap reference circuit with sub-1-V operation",  
  5. ^ P. Malcovati, F. Maloberti, C. Fiocchi, and M. Pruzzi, “Curvature-compensated bicmos bandgap with 1-V supply voltage,” IEEE J. Solid-State Circuits, vol. 36, no. 7, pp. 1076–1081, Jul. 2001.
  6. ^ Y. P. Tsividis, “Accurate analysis of temperature effects in Ic-Vbe characteristics with application to bandgap reference sources,” IEEE J. Solid-State Circuits, vol. 15, no. 6, pp. 1076 – 1084, Dec. 1980.
  7. ^ C. M. Andreou, S. Koudounas, and J. Georgiou, “A Novel Wide-Temperature-Range, 3.9ppm/oC CMOS Bandgap Reference Circuit,” IEEE Journal of Solid-State Circuits, vol.47, no. 2, pp. 574–581, Jan. 2012, doi:10.1109/JSSC.2011.2173267
  8. ^ S. Koudounas, C. M. Andreou and J. Georgiou, ”A Novel CMOS Bandgap Reference Circuit with Improved High-Order Temperature Compensation,” IEEE International Symposium on Circuits and Systems (ISCAS), Paris, France,2010 pp. 4073-4076, doi:10.1109/ISCAS.2010.5537621
  9. ^ , David F Hilbiber; United States Patent and Trademark Office; September 6, 1966.Reference voltage sourceUS Patent 3271660 -
  10. ^ ; Robert C Dobkin and Robert J Widlar; United States Patent and Trademark Office; November 2, 1971.Electrical regulator apparatus including a zero temperature coefficient voltage reference circuitUS Patent 3617859 -
  11. ^ ; Robert J Widlar; United States Patent and Trademark Office; February 3, 1981.Temperature compensated bandgap IC voltage referencesUS Patent 4249122 -
  12. ^ ; Robert C Dobkin; United States Patent and Trademark Office; May 8, 1984.Temperature compensated bandgap voltage reference circuitUS Patent 4447784 -

External links

  • The Design of Band-Gap Reference Circuits: Trials and Tribulations – Robert Pease, National Semiconductor
  • Features and Limitations of CMOS Voltage References
  • ECE 327: LM317 Bandgap Voltage Reference Example – Brief explanation of the temperature-independent bandgap reference circuit within the LM317.
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.