#jsDisabledContent { display:none; } My Account |  Register |  Help

# HSL and HSV

Article Id: WHEBN0000252814
Reproduction Date:

 Title: HSL and HSV Author: World Heritage Encyclopedia Language: English Subject: Collection: Color Space Publisher: World Heritage Encyclopedia Publication Date:

### HSL and HSV

Fig. 1. HSL (a–d) and HSV (e–h). Above (a, e): cut-away 3D models of each. Below: two-dimensional plots showing two of a model’s three parameters at once, holding the other constant: cylindrical shells (b, f) of constant saturation, in this case the outside surface of each cylinder; horizontal cross-sections (c, g) of constant HSL lightness or HSV value, in this case the slices halfway down each cylinder; and rectangular vertical cross-sections (d, h) of constant hue, in this case of hues 0° red and its complement 180° cyan.

HSL and HSV are the two most common cylindrical-coordinate representations of points in an RGB color model. The two representations rearrange the geometry of RGB in an attempt to be more intuitive and perceptually relevant than the cartesian (cube) representation. Developed in the 1970s for computer graphics applications, HSL and HSV are used today in color pickers, in image editing software, and less commonly in image analysis and computer vision.

HSL stands for hue, saturation, and lightness, and is also often called HLS. HSV stands for hue, saturation, and value, and is also often called HSB (B for brightness). A third model, common in computer vision applications, is HSI, for hue, saturation, and intensity. However, while typically consistent, these definitions are not standardized, and any of these abbreviations might be used for any of these three or several other related cylindrical models. (For technical definitions of these terms, see below.)

In each cylinder, the angle around the central vertical axis corresponds to "hue", the distance from the axis corresponds to "saturation", and the distance along the axis corresponds to "lightness", "value" or "brightness". Note that while "hue" in HSL and HSV refers to the same attribute, their definitions of "saturation" differ dramatically. Because HSL and HSV are simple transformations of device-dependent RGB models, the physical colors they define depend on the colors of the red, green, and blue primaries of the device or of the particular RGB space, and on the gamma correction used to represent the amounts of those primaries. Each unique RGB device therefore has unique HSL and HSV spaces to accompany it, and numerical HSL or HSV values describe a different color for each basis RGB space.[1]

Both of these representations are used widely in computer graphics, and one or the other of them is often more convenient than RGB, but both are also criticized for not adequately separating color-making attributes, or for their lack of perceptual uniformity. Other more computationally intensive models, such as CIELAB or CIECAM02 are said to better achieve these goals.

## Contents

• Basic principle 1
• Motivation 2
• Formal derivation 3
• Color-making attributes 3.1
• General approach 3.2
• Hue and chroma 3.3
• Lightness 3.4
• Saturation 3.5
• Examples 3.6
• Use in end-user software 4
• Use in image analysis 5
• Other cylindrical-coordinate color models 7
• Converting to RGB 8
• From HSV 8.1
• From HSL 8.2
• From luma/chroma/hue 8.3
• Swatches 9
• HSV 9.1
• HSL 9.2
• Notes and references 10
• Bibliography 11

## Basic principle

HSL and HSV are both cylindrical geometries (fig. 2), with hue, their angular dimension, starting at the red primary at 0°, passing through the green primary at 120° and the blue primary at 240°, and then wrapping back to red at 360°. In each geometry, the central vertical axis comprises the neutral, achromatic, or gray colors, ranging from black at lightness 0 or value 0, the bottom, to white at lightness 1 or value 1, the top. In both geometries, the additive primary and secondary colors – red, yellow, green, cyan, blue, and magenta – and linear mixtures between adjacent pairs of them, sometimes called pure colors, are arranged around the outside edge of the cylinder with saturation 1; in HSV these have value 1 while in HSL they have lightness ½. In HSV, mixing these pure colors with white – producing so-called tints – reduces saturation, while mixing them with black – producing shades – leaves saturation unchanged. In HSL, both tints and shades have full saturation, and only mixtures with both black and white – called tones – have saturation less than 1.

Fig. 3a–b. If we plot hue and (a) HSL lightness or (b) HSV value against chroma rather than saturation, the resulting solid is a bicone or cone, respectively, not a cylinder. Such diagrams often claim to represent HSL or HSV directly, with the chroma dimension deceptively labeled "saturation".

Because these definitions of saturation – in which very dark (in both models) or very light (in HSL) near-neutral colors, for instance or , are considered fully saturated – conflict with the intuitive notion of color purity, often a conic or bi-conic solid is drawn instead (fig. 3), with what this article calls chroma as its radial dimension, instead of saturation. Confusingly, such diagrams usually label this radial dimension "saturation", blurring or erasing the distinction between saturation and chroma.[2] As described below, computing chroma is a helpful step in the derivation of each model. Because such an intermediate model – with dimensions hue, chroma, and HSV value or HSL lightness – takes the shape of a cone or bicone, HSV is often called the "hexcone model" while HSL is often called the "bi-hexcone model" (fig. 8).[3]

## Motivation

Fig. 4. Painters long mixed colors by combining relatively bright pigments with black and white. Mixtures with white are called tints, mixtures with black are called shades, and mixtures with both are called tones. See Tints and shades.[4]
Fig. 5. This 1916 color model by German chemist hue circle, and colors of each hue into a triangle. The model thus takes the shape of a bicone.[5]
Fig. 7. Tektronix graphics terminals used the earliest commercial implementation of HSL, in 1979. This diagram, from a patent filed in 1983, shows the bicone geometry underlying the model.[6]

Most televisions, computer displays, and projectors produce colors by combining red, green, and blue light in varying intensities – the so-called RGB additive primary colors. The resulting mixtures in RGB color space can reproduce a wide variety of colors (called a gamut); however, the relationship between the constituent amounts of red, green, and blue light and the resulting color is unintuitive, especially for inexperienced users, and for users familiar with subtractive color mixing of paints or traditional artists’ models based on tints and shades (fig. 4). Furthermore, neither additive nor subtractive color models define color relationships the same way the human eye does.[7]

For example, imagine we have an RGB display whose color is controlled by three sliders ranging from 0–255, one controlling the intensity of each of the red, green, and blue primaries. If we begin with a relatively colorful orange , with sRGB values R = 217, G = 118, B = 33, and want to reduce its colorfulness by half to a less saturated orange , we would need to drag the sliders to decrease R by 31, increase G by 24, and increase B by 59, as pictured below.

In an attempt to accommodate more traditional and intuitive color mixing models, computer graphics pioneers at human vision in terms of other color-making attributes, such as hue, lightness, and chroma; as well as upon traditional color mixing methods – e.g., in painting – that involve mixing brightly colored pigments with black or white to achieve lighter, darker, or less colorful colors.

The following year, 1979, at SIGGRAPH, Tektronix introduced graphics terminals using HSL for color designation, and the Computer Graphics Standards Committee recommended it in their annual status report (fig. 7). These models were useful not only because they were more intuitive than raw RGB values, but also because the conversions to and from RGB were extremely fast to compute: they could run in real time on the hardware of the 1970s. Consequently, these models and similar ones have become ubiquitous throughout image editing and graphics software since then. Some of their uses are described below.[8][9][10][11][12][13]

## Formal derivation

Fig. 8. The geometric derivation of the cylindrical HSL and HSV representations of an RGB "colorcube".

### Color-making attributes

The dimensions of the HSV and HSL geometries – simple transformations of the not-perceptually-based RGB model – are not directly related to the photometric color-making attributes of the same names, as defined by scientists such as the CIE or ASTM. Nonetheless, it is worth reviewing those definitions before leaping into the derivation of our models.[14][15][16]

Hue
The "attribute of a visual sensation according to which an area appears to be similar to one of the perceived colors: red, yellow, green, and blue, or to a combination of two of them".
The total amount of light passing through a particular area.
Luminance (Y)
The radiance weighted by the effect of each wavelength on a typical human observer, measured in candela per square meter (cd/m2). Often the term luminance is used for the relative luminance, Y/Yn, where Yn is the luminance of the reference white point.
Luma (Y′)
The weighted sum of gamma-corrected R, G, and B values, and used in Y′CbCr, for JPEG compression and video transmission.
Brightness
The "attribute of a visual sensation according to which an area appears to emit more or less light".
Lightness, value
The "brightness relative to the brightness of a similarly illuminated white".
Colorfulness
The "attribute of a visual sensation according to which the perceived color of an area appears to be more or less chromatic".
Chroma
The "colorfulness relative to the brightness of a similarly illuminated white".
Saturation
The "colorfulness of a stimulus relative to its own brightness".

Brightness and colorfulness are absolute measures, which usually describe the spectral distribution of light entering the eye, while lightness and chroma are measured relative to some white point, and are thus often used for descriptions of surface colors, remaining roughly constant even as brightness and colorfulness change with different illumination. Saturation can be defined as either the ratio of colorfulness to brightness or of chroma to lightness.

### General approach

HSL, HSV, and related models can be derived via geometric strategies, or can be thought of as specific instances of a "generalized LHS model". The HSV and HSL model-builders took an RGB cube – with constituent amounts of red, green, and blue light in a color denoted R, G, B [0, 1][17] – and tilted it on its corner, so that black rested at the origin with white directly above it along the vertical axis, then measured the hue of the colors in the cube by their angle around that axis, starting with red at 0°. Then they came up with a characterization of brightness/value/lightness, and defined saturation to range from 0 along the axis to 1 at the most colorful point for each pair of other parameters.[4][9][10]

### Hue and chroma

Fig. 9. Both hue and chroma are defined based on the projection of the RGB cube onto a hexagon in the "chromaticity plane". Chroma is the relative size of the hexagon passing through a point, and hue is how far around that hexagon’s edge the point lies.

In each of our models, we calculate both hue and what this article will call chroma, after Joblove and Greenberg, in the same way – that is, the hue of a color has the same numerical values in all of these models, as does its chroma. If we take our tilted RGB cube, and project it onto the "chromaticity plane" perpendicular to the neutral axis, our projection takes the shape of a hexagon, with red, yellow, green, cyan, blue, and magenta at its corners (fig. 9). Hue is roughly the angle of the vector to a point in the projection, with red at 0°, while chroma is roughly the distance of the point from the origin.[18][19]

More precisely, both hue and chroma in this model are defined with respect to the hexagonal shape of the projection. The chroma is the proportion of the distance from the origin to the edge of the hexagon. In the lower part of the diagram to the right, this is the ratio of lengths OP/OP, or alternately the ratio of the radii of the two hexagons. This ratio is the difference between the largest and smallest values among R, G, or B in a color. To make our definitions easier to write, we’ll define these maximum and minimum component values as M and m, respectively.[20]

\begin{align} M &= \operatorname{max}(R, G, B) \\ m &= \operatorname{min}(R, G, B) \\ C &= M - m \end{align}

To understand why chroma can be written as Mm, notice that any neutral color, with R = G = B, projects onto the origin and so has 0 chroma. Thus if we add or subtract the same amount from all three of R, G, and B, we move vertically within our tilted cube, and do not change the projection. Therefore, the two colors (R, G, B) and (Rm, Gm, Bm) project on the same point, and have the same chroma. The chroma of a color with one of its components equal to zero (m = 0) is simply the maximum of the other two components. This chroma is M in the particular case of a color with a zero component, and Mm in general.

The hue is the proportion of the distance around the edge of the hexagon which passes through the projected point, originally measured on the range [0, 1) but now typically measured in degrees [0°, 360°). For points which project onto the origin in the chromaticity plane (i.e., grays), hue is undefined. Mathematically, this definition of hue is written piecewise:[21]

\begin{align} H^\prime &= \begin{cases} \mathrm{undefined}, &\mbox{if } C = 0 \\ \frac{G - B}{C} \;\bmod 6, &\mbox{if } M = R \\ \frac{B - R}{C} + 2, &\mbox{if } M = G \\ \frac{R - G}{C} + 4, &\mbox{if } M = B \end{cases} \\ H &= 60^\circ \times H^\prime \end{align}

Sometimes, neutral colors (i.e. with C = 0) are assigned a hue of 0° for convenience of representation.

Fig. 10. The definitions of hue and chroma in HSL and HSV have the effect of warping hexagons into circles.

These definitions amount to a geometric warping of hexagons into circles: each side of the hexagon is mapped linearly onto a 60° arc of the circle (fig. 10). After such a transformation, hue is precisely the angle around the origin and chroma the distance from the origin: the angle and magnitude of the vector pointing to a color.

Fig. 11. Constructing rectangular chromaticity coordinates α and β, and then transforming those into hue H2 and chroma C2 yields slightly different values than computing hexagonal hue H and chroma C: compare the numbers in this diagram to those earlier in this section.

Instead of measuring hue and chroma with reference to the hexagonal edge of the projection of the RGB cube into the plane perpendicular to its neutral axis, we can define chromaticity coordinates alpha and beta in the plane – with alpha pointing in the direction of red, and beta perpendicular to it – and then define hue H2 and chroma C2 as the polar coordinates of these. That is, the tangent of hue is beta over alpha, and chroma squared is alpha squared plus beta squared.

Sometimes for image analysis applications, this hexagon-to-circle transformation is skipped, and hue and chroma (we’ll denote these H2 and C2) are defined by the usual cartesian-to-polar coordinate transformations (fig. 11). The easiest way to derive those is via a pair of cartesian chromaticity coordinates which we’ll call α and β:[22][23][24]

\begin{align} \alpha &= \textstyle{\frac{1}{2}}(2R - G - B) \\ \beta &= \textstyle{\frac{\sqrt{3}}{2}}(G - B) \\ H_2 &= \operatorname{atan2}(\beta, \alpha) \\ C_2 &= \sqrt{\alpha^2 + \beta^2} \end{align}

(The atan2 function, a "two-argument arctangent", computes the angle from a cartesian coordinate pair.)

Notice that these two definitions of hue (H and H2) nearly coincide, with a maximum difference between them for any color of about 1.12° – which occurs at twelve particular hues, for instance H = 13.38°, H2 = 12.26° – and with H = H2 for every multiple of 30°. The two definitions of chroma (C and C2) differ more substantially: they are equal at the corners of our hexagon, but at points halfway between two corners, such as H = H2 = 30°, we have C = 1, but C2 = ¾ ≈ 0.866, a difference of about 13.4%.

### Lightness

Fig. 12a–d. Four different possible "lightness" dimensions, plotted against chroma, for a pair of complementary hues. Each plot is a vertical cross-section of its three-dimensional color solid.

While the definition of hue is relatively uncontroversial – it roughly satisfies the criterion that colors of the same perceived hue should have the same numerical hue – the definition of a lightness or value dimension is less obvious: there are several possibilities depending on the purpose and goals of the representation. Here are four of the most common (fig. 12; three of these are also shown in fig. 8):

• The simplest definition is just the average of the three components, in the HSI model called intensity (fig. 12a). This is simply the projection of a point onto the neutral axis – the vertical height of a point in our tilted cube. The advantage is that, together with Euclidean-distance calculations of hue and chroma, this representation preserves distances and angles from the geometry of the RGB cube.[23][25]
I = \textstyle{\frac{1}{3}}(R + G + B)\,\!
• In the HSV "hexcone" model, value is defined as the largest component of a color, our M above (fig. 12b). This places all three primaries, and also all of the "secondary colors" – cyan, yellow, and magenta – into a plane with white, forming a hexagonal pyramid out of the RGB cube.[9]
V = M\,\!
• In the HSL "bi-hexcone" model, lightness is defined as the average of the largest and smallest color components (fig. 12c). This definition also puts the primary and secondary colors into a plane, but a plane passing halfway between white and black. The resulting color solid is a double-cone similar to Ostwald’s, shown above.[10]
L = \textstyle{\frac{1}{2}}(M + m)\,\!
• A more perceptually relevant alternative is to use luma, Y, as a lightness dimension (fig. 12d). Luma is the weighted average of gamma-corrected R, G, and B, based on their contribution to perceived luminance, long used as the monochromatic dimension in color television broadcast. For the Rec. 709 primaries used in sRGB, Y709 = 0.21R + 0.72G + 0.07B; for the Rec. 601 NTSC primaries, Y601 = 0.30R + 0.59G + 0.11B; for other primaries different coefficients should be used.[15][26][27]
Y^\prime_{601} = 0.30R + 0.59G + 0.11B\,\!

All four of these leave the neutral axis alone. That is, for colors with R = G = B, any of the four formulations yields a lightness equal to the value of R, G, or B.

For a graphical comparison, see fig. 13 below.

### Saturation

Fig. 14a–d. In both HSL and HSV, saturation is simply the chroma scaled to fill the interval [0, 1] for every combination of hue and lightness or value.

If we encode colors in a hue/lightness/chroma or hue/value/chroma model (using the definitions from the previous two sections), not all combinations of lightness (or value) and chroma are meaningful: that is, half of the colors we can describe using H ∈ [0°, 360°), C ∈ [0, 1], and V ∈ [0, 1] fall outside the RGB gamut (the gray parts of the slices in figure 14). The creators of these models considered this a problem for some uses. For example, in a color selection interface with two of the dimensions in a rectangle and the third on a slider, half of that rectangle is made of unused space. Now imagine we have a slider for lightness: the user’s intent when adjusting this slider is potentially ambiguous: how should the software deal with out-of-gamut colors? Or conversely, If the user has selected as colorful as possible a dark purple , and then shifts the lightness slider upward, what should be done: would the user prefer to see a lighter purple still as colorful as possible for the given hue and lightness , or a lighter purple of exactly the same chroma as the original color ?[10]

To solve problems such as these, the HSL and HSV models scale the chroma so that it always fits into the range [0, 1] for every combination of hue and lightness or value, calling the new attribute saturation in both cases (fig. 14). To calculate either, simply divide the chroma by the maximum chroma for that value or lightness.

\begin{align} S_{HSV} &= \begin{cases} 0, &\mbox{if } C = 0 \\ \frac{C}{V}, &\mbox{otherwise} \end{cases} \\ S_{HSL} &= \begin{cases} 0, &\mbox{if } C = 0 \\ \frac{C}{1 - |2L - 1|}, &\mbox{otherwise} \end{cases} \end{align}
Fig. 15a–b. In HSI, saturation, shown in the slice on the right, is roughly the chroma relative to lightness. Also common is a model with dimensions I, H2, C2, shown in the slice on the left. Notice that the hue in these slices is the same as the hue above, but H differs slightly from H2

The HSI model commonly used for computer vision, which takes H2 as a hue dimension and the component average I ("intensity") as a lightness dimension, does not attempt to "fill" a cylinder by its definition of saturation. Instead of presenting color choice or modification interfaces to end users, the goal of HSI is to facilitate separation of shapes in an image. Saturation is therefore defined in line with the psychometric definition: chroma relative to lightness (fig. 15). See the Use in image analysis section of this article.[28]

S_{HSI} = \begin{cases} 0, &\mbox{if } C=0 \\ 1 - \frac{m}{I}, &\mbox{otherwise} \end{cases}

Using the same name for these three different definitions of saturation leads to some confusion, as the three attributes describe substantially different color relationships; in HSV and HSI, the term roughly matches the psychometric definition, of a chroma of a color relative to its own lightness, but in HSL it does not come close. Even worse, the word saturation is also often used for one of the measurements we call chroma above (C or C2).

### Examples

All parameter values shown below are in the interval [0, 1], except those for H and H2 which are in the interval [0°, 360°).[29]

Color R G B H H2 C C2 V L I Y′601 SHSV SHSL SHSI
#FFFFFF 1.000 1.000 1.000 n/a n/a 0.000 0.000 1.000 1.000 1.000 1.000 0.000 0.000 0.000
#808080 0.500 0.500 0.500 n/a n/a 0.000 0.000 0.500 0.500 0.500 0.500 0.000 0.000 0.000
#000000 0.000 0.000 0.000 n/a n/a 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000 0.000
#FF0000 1.000 0.000 0.000 0.0° 0.0° 1.000 1.000 1.000 0.500 0.333 0.299 1.000 1.000 1.000
#BFBF00 0.750 0.750 0.000 60.0° 60.0° 0.750 0.750 0.750 0.375 0.500 0.664 1.000 1.000 1.000
#008000 0.000 0.500 0.000 120.0° 120.0° 0.500 0.500 0.500 0.250 0.167 0.293 1.000 1.000 1.000
#80FFFF 0.500 1.000 1.000 180.0° 180.0° 0.500 0.500 1.000 0.750 0.833 0.850 0.500 1.000 0.400
#8080FF 0.500 0.500 1.000 240.0° 240.0° 0.500 0.500 1.000 0.750 0.667 0.557 0.500 1.000 0.250
#BF40BF 0.750 0.250 0.750 300.0° 300.0° 0.500 0.500 0.750 0.500 0.583 0.457 0.667 0.500 0.571
#A0A424 0.628 0.643 0.142 61.8° 61.5° 0.501 0.494 0.643 0.393 0.471 0.581 0.779 0.638 0.699
#411BEA 0.255 0.104 0.918 251.1° 250.0° 0.814 0.750 0.918 0.511 0.426 0.242 0.887 0.832 0.756
#1EAC41 0.116 0.675 0.255 134.9° 133.8° 0.559 0.504 0.675 0.396 0.349 0.460 0.828 0.707 0.667
#F0C80E 0.941 0.785 0.053 49.5° 50.5° 0.888 0.821 0.941 0.497 0.593 0.748 0.944 0.893 0.911
#B430E5 0.704 0.187 0.897 283.7° 284.8° 0.710 0.636 0.897 0.542 0.596 0.423 0.792 0.775 0.686
#ED7651 0.931 0.463 0.316 14.3° 13.2° 0.615 0.556 0.931 0.624 0.570 0.586 0.661 0.817 0.446
#FEF888 0.998 0.974 0.532 56.9° 57.4° 0.466 0.454 0.998 0.765 0.835 0.931 0.467 0.991 0.363
#19CB97 0.099 0.795 0.591 162.4° 163.4° 0.696 0.620 0.795 0.447 0.495 0.564 0.875 0.779 0.800
#362698 0.211 0.149 0.597 248.3° 247.3° 0.448 0.420 0.597 0.373 0.319 0.219 0.750 0.601 0.533
#7E7EB8 0.495 0.493 0.721 240.5° 240.4° 0.228 0.227 0.721 0.607 0.570 0.520 0.316 0.290 0.135

## Use in end-user software

Fig 16a–g. By the 1990s, HSL and HSV color selection tools were ubiquitous. The screenshots above are taken from: (a) SGI IRIX 5, c. 1995; (b) Adobe Photoshop, c. 1990; (c) IBM OS/2 Warp 3, c. 1994; (d) Apple Macintosh System 7, c. 1996; (e) Fractal Design Painter, c. 1993; (f) Microsoft Windows 3.1, c. 1992; (g) NeXTSTEP, c. 1995. These are undoubtedly based on earlier examples, stretching back to PARC and NYIT in the mid-1970s.[30]

The original purpose of HSL and HSV and similar models, and their most common current application, is in color selection tools. At their simplest, some such color pickers provide three sliders, one for each attribute. Most, however, show a two-dimensional slice through the model, along with a slider controlling which particular slice is shown. The latter type of GUI exhibits great variety, because of the choice of cylinders, hexagonal prisms, or cones/bicones that the models suggest (see the diagram near the top of the page). Several color choosers from the 1990s are shown to the right, most of which have remained nearly unchanged in the intervening time: today, nearly every computer color chooser uses HSL or HSV, at least as an option. Some more sophisticated variants are designed for choosing whole sets of colors, basing their suggestions of compatible colors on the HSL or HSV relationships between them.[31]

Most web applications needing color selection also base their tools on HSL or HSV, and pre-packaged open source color choosers exist for most major web front-end frameworks. The CSS 3 specification allows web authors to specify colors for their pages directly with HSL coordinates.[32]

HSL and HSV are sometimes used to define gradients for data visualization, as in maps or medical images. For example, the popular GIS program ArcGIS historically applied customizable HSV-based gradients to numerical geographical data.[33]

 Fig. 17. xv’s HSV-based color modifier. Fig. 18. The hue/saturation tool in Photoshop 2.5, ca. 1992 Fig. 19. Avid’s video color adjustment tool, based on HSL or a similar model.

Image editing software also commonly includes tools for adjusting colors with reference to HSL or HSV coordinates, or to coordinates in a model based on the "intensity" or luma defined above. In particular, tools with a pair of "hue" and "saturation" sliders are commonplace, dating to at least the late-1980s, but various more complicated color tools have also been implemented. For instance, the Unix image viewer and color editor xv allowed six user-definable hue (H) ranges to be rotated and resized, included a dial-like control for saturation (SHSV), and a curves-like interface for controlling value (V) – see fig. 17. The image editor Picture Window Pro includes a "color correction" tool which affords complex remapping of points in a hue/saturation plane relative to either HSL or HSV space.[34]

Video editors also use these models. For example, both Avid and Final Cut Pro include color tools based on HSL or a similar geometry for use adjusting the color in video. With the Avid tool, users pick a vector by clicking a point within the hue/saturation circle to shift all the colors at some lightness level (shadows, mid-tones, highlights) by that vector.

Since version 4.0, Adobe Photoshop’s "Luminosity", "Hue", "Saturation", and "Color" blend modes composite layers using a luma/chroma/hue color geometry. These have been copied widely, but several imitators use the HSL (e.g. PhotoImpact, Paint Shop Pro) or HSV (e.g. GIMP) geometries instead.[35]

## Use in image analysis

HSL, HSV, HSI, or related models are often used in computer vision and image analysis for feature detection or image segmentation. The applications of such tools include object detection, for instance in robot vision; object recognition, for instance of faces, text, or license plates; content-based image retrieval; and analysis of medical images.[28]

For the most part, computer vision algorithms used on color images are straightforward extensions to algorithms designed for grayscale images, for instance k-means or fuzzy clustering of pixel colors, or canny edge detection. At the simplest, each color component is separately passed through the same algorithm. It is important, therefore, that the features of interest can be distinguished in the color dimensions used. Because the R, G, and B components of an object’s color in a digital image are all correlated with the amount of light hitting the object, and therefore with each other, image descriptions in terms of those components make object discrimination difficult. Descriptions in terms of hue/lightness/chroma or hue/lightness/saturation are often more relevant.[28]

Starting in the late 1970s, transformations like HSV or HSI were used as a compromise between effectiveness for segmentation and computational complexity. They can be thought of as similar in approach and intent to the neural processing used by human color vision, without agreeing in particulars: if the goal is object detection, roughly separating hue, lightness, and chroma or saturation is effective, but there is no particular reason to strictly mimic human color response. John Kender’s 1976 master’s thesis proposed the HSI model. Ohta et al. (1980) instead used a model made up of dimensions similar to those we have called I, α, and β. In recent years, such models have continued to see wide use, as their performance compares favorably with more complex models, and their computational simplicity remains compelling.[36][37][38][28][39]

Fig 20a. The sRGB gamut mapped in CIELAB space. Notice that the lines pointing to the red, green, and blue primaries are not evenly spaced by hue angle, and are of unequal length. The primaries also have different L* values.
b. The Adobe RGB gamut mapped in CIELAB space. Also notice that these two RGB spaces have different gamuts, and thus will have different HSL and HSV representations.

While HSL, HSV, and related spaces serve well enough to, for instance, choose a single color, they ignore much of the complexity of color appearance. Essentially, they trade off perceptual relevance for computation speed, from a time in computing history (high-end 1970s graphics workstations, or mid-1990s consumer desktops) when more sophisticated models would have been too computationally expensive.[40]

HSL and HSV are simple transformations of RGB which preserve symmetries in the RGB cube unrelated to human perception, such that its R, G, and B corners are equidistant from the neutral axis, and equally spaced around it. If we plot the RGB gamut in a more perceptually-uniform space, such as CIELAB (see below), it becomes immediately clear that the red, green, and blue primaries do not have the same lightness or chroma, or evenly spaced hues. Furthermore, different RGB displays use different primaries, and so have different gamuts. Because HSL and HSV are defined purely with reference to some RGB space, they are not absolute color spaces: to specify a color precisely requires reporting not only HSL or HSV values, but also the characteristics of the RGB space they are based on, including the gamma correction in use.

If we take an image and extract the hue, saturation, and lightness or value components, and then compare these to the components of the same name as defined by color scientists, we can quickly see the difference, perceptually. For example, examine the following images of a fire breather (fig. 13). CIELAB L* is a CIE-defined quantity intended to match perceptual lightness response, and it is plain that L* appears similar in lightness to the original color image. Luma is roughly similar, but differs somewhat at high chroma. HSL L and HSV V, by contrast, diverge substantially from perceptual lightness.

b. CIELAB L*
c. Rec. 601 luma Y
d. Component average: "intensity" I
e. HSV value V
f. HSL lightness L

Though none of the dimensions in these spaces match their perceptual analogs, the value of HSV and the saturation of HSL are particular offenders. In HSV, the blue primary and white are held to have the same value, even though perceptually the blue primary has somewhere around 10% of the luminance of white (the exact fraction depends on the particular RGB primaries in use). In HSL, a mix of 100% red, 100% green, 90% blue – that is, a very light yellow – is held to have the same saturation as the green primary , even though the former color has almost no chroma or saturation by the conventional psychometric definitions. Such perversities led Cynthia Brewer, expert in color scheme choices for maps and information displays, to tell the American Statistical Association:

Computer science offers a few poorer cousins to these perceptual spaces that may also turn up in your software interface, such as HSV and HLS. They are easy mathematical transformations of RGB, and they seem to be perceptual systems because they make use of the hue–lightness/value–saturation terminology. But take a close look; don’t be fooled. Perceptual color dimensions are poorly scaled by the color specifications that are provided in these and some other systems. For example, saturation and lightness are confounded, so a saturation scale may also contain a wide range of lightnesses (for example, it may progress from white to green which is a combination of both lightness and saturation). Likewise, hue and lightness are confounded so, for example, a saturated yellow and saturated blue may be designated as the same ‘lightness’ but have wide differences in perceived lightness. These flaws make the systems difficult to use to control the look of a color scheme in a systematic manner. If much tweaking is required to achieve the desired effect, the system offers little benefit over grappling with raw specifications in RGB or CMY.[41]

If these problems make HSL and HSV problematic for choosing colors or color schemes, they make them much worse for image adjustment. HSL and HSV, as Brewer mentioned, confound perceptual color-making attributes, so that changing any dimension results in non-uniform changes to all three perceptual dimensions, and distorts all of the color relationships in the image. For instance, rotating the hue of a pure dark blue toward green will also reduce its perceived chroma, and increase its perceived lightness (the latter is grayer and lighter), but the same hue rotation will have the opposite impact on lightness and chroma of a lighter bluish-green – to (the latter is more colorful and slightly darker). In the example below (fig. 21), the image on the left (a) is the original photograph of a green turtle. In the middle image (b), we have rotated the hue (H) of each color by −30°, while keeping HSV value and saturation or HSL lightness and saturation constant. In the image on the right (c), we make the same rotation to the HSL/HSV hue of each color, but then we force the CIELAB lightness (L*, a decent approximation of perceived lightness) to remain constant. Notice how the hue-shifted middle version without such a correction dramatically changes the perceived lightness relationships between colors in the image. In particular, the turtle’s shell is much darker and has less contrast, and the background water is much lighter.

b. HSL/HSV hue of each color shifted by −30°
c. Hue shifted but CIELAB lightness (L*) kept as in the original

Because hue is a circular quantity, represented numerically with a discontinuity at 360°, it is difficult to use in statistical computations or quantitative comparisons: analysis requires the use of circular statistics. Furthermore, hue is defined piecewise, in 60° chunks, where the relationship of lightness, value, and chroma to R, G, and B depends on the hue chunk in question. This definition introduces discontinuities, corners which can plainly be seen in horizontal slices of HSL or HSV.[42][43]

Charles Poynton, digital video expert, lists the above problems with HSL and HSV in his Color FAQ, and concludes that:

HSB and HLS were developed to specify numerical Hue, Saturation and Brightness (or Hue, Lightness and Saturation) in an age when users had to specify colors numerically. The usual formulations of HSB and HLS are ﬂawed with respect to the properties of color vision. Now that users can choose colors visually, or choose colors related to other media (such as PANTONE), or use perceptually-based systems like L*u*v* and L*a*b*, HSB and HLS should be abandoned.[44]

## Other cylindrical-coordinate color models

Fig. 22. Runge’s Farbenkugel, 1810.
Fig. 23. Munsell’s balanced color sphere, 1900, from A Color Notation, 1905.

The creators of HSL and HSV were far from the first to imagine colors fitting into conic or spherical shapes, with neutrals running from black to white in a central axis, and hues corresponding to angles around that axis. Similar arrangements date back to the 18th century, and continue to be developed in the most modern and scientific models. A pair of the most influential older models are