World Library  
Flag as Inappropriate
Email this Article

Multi-layer insulation

Article Id: WHEBN0008559743
Reproduction Date:

Title: Multi-layer insulation  
Author: World Heritage Encyclopedia
Language: English
Subject: Space Infrastructure Servicing, Leonardo (ISS module), ADEOS II, Superconducting radio frequency, Propellant depot
Collection:
Publisher: World Heritage Encyclopedia
Publication
Date:
 

Multi-layer insulation

Closeup of Multi-layer insulation from a satellite. The metal coated plastic layers and the scrim separator are visible.

Multi-layer insulation, or MLI, is thermal insulation composed of multiple layers of thin sheets and is often used on spacecraft. It is one of the main items of the spacecraft thermal design, primarily intended to reduce heat loss by thermal radiation. In its basic form, it does not appreciably insulate against other thermal losses such as heat conduction or convection. It is therefore commonly used on satellites and other applications in vacuum where conduction and convection are much less significant and radiation dominates. MLI gives many satellites and other space probes the appearance of being covered with gold foil.

Function and design

The golden areas are MLI blankets on the Mars Reconnaissance Orbiter

The principle behind MLI is radiation balance. To see why it works, start with a concrete example - imagine a square meter of a surface in outer space, at 300 K, with an emissivity of 1, facing away from the sun or other heat sources. From the Stefan-Boltzmann law, this surface will radiate 460 watts. Now imagine placing a thin (but opaque) layer 1 cm away from the plate, thermally insulated from it, and also with an emissivity of 1. This new layer will cool until it is radiating 230 watts from each side, at which point everything is in balance. The new layer receives 460 watts from the original plate. 230 watts is radiated back to the original plate, and 230 watts to space. The original surface still radiates 460 watts, but gets 230 back from the new layers, for a net loss of 230 watts. So overall, the radiation losses have been reduced by half by adding the additional layer.

MLI covering the heat shield of the Huygens probe

More layers can be added to reduce the loss further. The blanket can be further improved by making the outside surfaces highly reflective to thermal radiation, which reduces both absorption and emission. The performance of a layer stack can be quantified in terms of its overall heat transfer coefficient U, which defines the radiative heat flow rate Q between two parallel surfaces with a temperature difference \Delta T and area A as

Q = U A \Delta T.

Theoretically, the heat transfer coefficient between two layers with emissivities \epsilon_1 and \epsilon_2, under vacuum, is

U = 4\sigma T^3 \frac{1}{1/\epsilon_1 + 1/\epsilon_2 - 1},

where T is the mean of the temperatures (in K) of the two layers and \sigma=5.7\times10^{-8} Wm−2K−4 is the Stefan-Boltzmann Constant. If each layer has the same emissivity \epsilon on both sides, then a stack of N layers placed between two high-emissivity surfaces will have an overall heat transfer coefficient

U = 4\sigma T^3 \frac{1}{N(2/\epsilon - 1) + 1}.

Clearly, increasing the number of layers and decreasing the emissivity both lower the heat transfer coefficient, which is equivalent to a higher insulation value. In this equation, it is assumed that the temperature difference is small compared to the absolute temperature. In space, where the apparent outside temperature could be 3 K (cosmic background radiation), the exact U value is different.

Aluminum coated on both sides of these MLI sheets with thicker outer layer (left), white netting spacer (middle), and thinner inner layer (right) which is also crinkled to provide additional separation between the layers. The sheets are perforated to allow air passage during launch.

The layers of MLI can be arbitrarily close to each other, as long as they are not in thermal contact. The separation space only needs to be minute, which is the function of the extremely thin scrim or polyester 'bridal veil' as shown in the photo. To reduce weight and blanket thickness, the internal layers are made very thin, but they must be opaque to thermal radiation. Since they don't need much structural strength, these internal layers are usually made of very thin plastic, about 6 micrometres (1/4 mil) thick, such as Mylar or Kapton, coated on one side with a thin layer of metal on both sides, typically silver or aluminium.[1] For compactness, the layers are spaced as close to each other as possible, though without touching, since there should be little or no thermal conduction between the layers. A typical insulation blanket has 40 or more layers.[1] The layers may be embossed or crinkled, so they only touch at a few points, or held apart by a thin cloth mesh, or scrim, which can be seen in the picture above. The outer layers must be stronger, and are often thicker and stronger plastic, re-enforced with a stronger scrim material such as fiberglass.

In satellite applications, the MLI will be full of air at launch time. As the rocket ascends, this air must be able to escape without damaging the blanket. This may require holes or perforations in the layers,[2] even though this reduces their effectiveness.[3]

MLI blankets are constructed with sewing technology. The layers are cut, stacked on top of each other, and sewn together at the edges. Seams and gaps in the insulation are responsible for most of the heat leakage through MLI blankets. A new method is being developed to use polyetheretherketone (PEEK) tag pins (similar to plastic hooks used to attach price tags to garments) to fix the film layers in place instead of sewing to improve the thermal performance.[3]

Additional properties

Spacecraft also may use MLI as a first line of defense against dust impacts. This normally means spacing it a cm or so away from the surface it is insulating. Also, one or more of the layers may be replaced by a mechanically strong material, such as beta cloth.

In some applications the insulating layers must be grounded, so they cannot build up a charge and arc, causing radio interference. Since the normal construction results in electrical as well as thermal insulation, these applications may include aluminum spacers as opposed to cloth scrim at the points where the blankets are sewn together.

See also

References

  1. ^ a b Savage, Chris J. (2003). "11. Thermal Control of Spacecraft". In Peter W. Fortescue, John Stark, Graham Swinerd. Spacecraft Systems Engineering (3 ed.). John Wiley and Sons. pp. 378–379.  
  2. ^ "Perforating". Dunmore. Retrieved 27 April 2014. 
  3. ^ a b Ryuta Hatakenaka; Takeshi Miyakita; Hiroyuki Sugita (14–18 July 2013). "Thermal Performance and Practical Utility of a MLI Blanket using Plastic Pins for Space Use". 43rd International Conference on Environmental Systems 2013 : Vail, Colorado, USA, 14-18 July 2013.. p. 2432.  
  • Satellite Thermal Control Handbook, ed. David Gilmore. ISBN 1-884989-00-4. In particular, Chapter 5, Insulation, by Martin Donabedian and David Gilmore.
  • Tutorial on temperature control of spacecraft by JPL
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and USA.gov, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for USA.gov and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
 
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
 
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.
 


Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.