World Library  
Flag as Inappropriate
Email this Article

Passivation (chemistry)

Article Id: WHEBN0000175622
Reproduction Date:

Title: Passivation (chemistry)  
Author: World Heritage Encyclopedia
Language: English
Subject: Stainless steel, Chromium, Bluing (steel), Oxide, High-temperature corrosion
Collection: Corrosion Prevention
Publisher: World Heritage Encyclopedia

Passivation (chemistry)

Passivation, in physical chemistry and engineering, refers to a material becoming "passive," that is, being less affected by environmental factors such as air and water. Passivation involves a shielding outer-layer of base material, which can be applied as a microcoating, or which occurs spontaneously in nature. As a technique, passivation is the use of a light coat of a protective material, such as metal oxide, to create a shell against corrosion. Passivation can occur only in certain conditions, and is used in microelectronics to enhance silicon.[1] The technique of passivation is used to strengthen and preserve the appearance of metallics.

When exposed to air, many metals naturally form a hard, relatively inert surface, as in the tarnishing of silver, in contrast to metals such as iron, where uniform corrosion produces a somewhat rough surface by removing a substantial amount of metal, which either dissolves in the environment or reacts with it to produce a loosely adherent, porous coating of corrosion products. The amount by which a corrosion coating reduces the rate of corrosion varies, depending on the kind of metal and its environment, and is notably slower in room-temperature air for aluminium, chromium, zinc, titanium, and silicon (a metalloid); the shell inhibits deeper corrosion, and so is the key factor of passivation. The inert surface layer, termed the ‘’native oxide layer‘’, is usually an oxide or a nitride, with a thickness of a monolayer (1-3 Å) for a noble metal such as platinum, about 15 Å for silicon, and nearer to 50 Å for aluminium after several years.[2][3][4]


  • Mechanisms 1
  • Specific materials 2
    • Silicon 2.1
    • Aluminium 2.2
    • Ferrous materials 2.3
      • Stainless steel 2.3.1
    • Nickel 2.4
  • See also 3
  • References 4
  • Further reading 5


Pourbaix diagram of iron.[5]

There has been much interest in determining the mechanisms which describe how the thickness of the oxide layer on a material increases with time. Some of the important issues include: the relative volume of the oxide compared to the parent metal, the mechanism by which oxygen diffuses through the metal oxide to the metal - oxide interface and the relative chemical potential for the oxide to form. Boundaries between micro grains, if the oxide layer is crystalline, form an important pathway for oxygen to reach the unoxidized metal below. For this reason, vitreous oxide coatings – which lack grain boundaries – can retard oxidation.[6] The conditions necessary (but not sufficient) for passivation are recorded in Pourbaix diagrams. Some corrosion inhibitors help the formation of a passivation layer on the surface of the metals to which they are applied. Some compounds, dissolving in solutions (chromates, molybdates) form non-reactive and low solubility films on metal surfaces.

Specific materials


In the area of microelectronics, the formation of a strongly adhering passivating oxide is important to the performance of silicon.

In the area of photovoltaics, a passivating surface layer such as silicon nitride, silicon dioxide or titanium dioxide can reduce surface recombination - a significant loss mechanism in solar cells.


Pure aluminium naturally forms a thin surface layer of aluminium oxide on contact with oxygen in the atmosphere through a process called oxidation, which creates a physical barrier to corrosion or further oxidation in most environments. Aluminium alloys, however, offer little protection against corrosion. There are three main ways to passivate these alloys: alclading, chromate conversion coating and anodizing. Alclading is the process of metallurgically bonding a thin layer of pure aluminium to the aluminium alloy. Chromate conversion coating is a common way of passivating not only aluminum, but also zinc, cadmium, copper, silver, magnesium, and tin alloys. Anodizing forms a thick oxide coating. This finish is more robust than the other processes and also provides good electrical insulation, which the other two processes do not.

For example, prior to storing hydrogen peroxide in an aluminium container, the container can be passivated by rinsing it with a dilute solution of nitric acid and peroxide alternating with deionized water. The nitric acid and peroxide oxidizes and dissolves any impurities on the inner surface of the container, and the deionized water rinses away the acid and oxidized impurities.

Ferrous materials

Ferrous materials, including steel, may be somewhat protected by promoting oxidation ("rust") and then converting the oxidation to a metalophosphate by using phosphoric acid and further protected by surface coating. As the uncoated surface is water-soluble, a preferred method is to form manganese or zinc compounds by a process commonly known as Parkerizing or phosphate conversion. Older, less-effective but chemically-similar electrochemical conversion coatings included black oxidizing, historically known as bluing or browning. Ordinary steel forms a passivating layer in alkali environments, as reinforcing bar does in concrete.

Stainless steel

  • U.S. government, QQ-P-35: Federal specification: Passivation treatments for corrosion-resistant steel (Rev C ed.). U.S. federal spec QQ-P-35 was superseded by AMS-QQ-P-35 on 4 April 1997 as part of the changeover instituted by the  
  • Chromate conversion coating (chemical film) per MIL-DTL-5541F for aluminium and aluminium alloy parts
  • A standard overview on black oxide coatings is provided in MIL-HDBK-205, Phosphate & Black Oxide Coating of Ferrous Metals. Many of the specifics of Black Oxide coatings may be found in MIL-DTL-13924 (formerly MIL-C-13924). This Mil-Spec document additionally identifies various classes of Black Oxide coatings, for use in a variety of purposes for protecting ferrous metals against rust.
  • Budinski, Kenneth G. (1988), Surface Engineering for Wear Resistance,  
  • Brimi, Marjorie A. (1965), Electrofinishing,  
  • Bockris, John O'M.; Reddy, Amulya K. N. (1977), Modern Electrochemistry: An Introduction to an Interdisciplinary Area 2, Plenum Press,  

Further reading

  1. ^ IUPAC Goldbook
  2. ^
  3. ^ O'M. Bockris 1977, p. 1325
  4. ^ Fehlner, Francis P, Low-Temperature Oxidation:The Role of Vitreous Oxides, A Wiley-Interscience Publication, John Wiley & Sons, New York , 1986 ISBN 0471-87448-5
  5. ^ University of Bath & Western Oregon University
  6. ^ Fehlner, Francis P, ref.3.
  7. ^ "Stainless Steel Passivation". Arrow Cryogenics. Retrieved 28 February 2014. 
  8. ^
  9. ^
  10. ^


See also

Nickel can be used for handling elemental fluorine, owing to the formation of a passivation layer of nickel fluoride. This fact is useful in water treatment and sewage treatment applications.


It is not uncommon for some aerospace manufacturers to have additional guidelines and regulations when passivating their product that exceed the requirements in a national standard. Often, these requirements will be flowed down using NADCAP or some other accreditation system. Various testing methods are available to determine the passivation (or passive state) of stainless steel. The most common methods for validating the passivity of a part is some combination of high humidity and heat for a period of time, intended to induce rusting. Electro-chemical testers can also be utilized to commercially verify passivation.

Common among all of the different specifications and types are the following steps: Prior to passivation, the parts must be cleaned of any contaminants and generally must undergo a validating test to prove that the surface is 'clean.' The part is then placed in an acidic passivating bath that meets the temperature and chemistry requirements of the Method and Type specified between customer and vendor. (Temperatures can range from ambient to 140 degrees Fahrenheit, while minimum passivation times are generally around 20 to 30 minutes). The parts are then neutralized using a bath of aqueous sodium hydroxide and then rinsed with clean water, dried, and the passive surface is validated using exposure to humidity, elevated temperature, a rusting agent (salt spray), or some combination of the three. However, proprietary passivation processes exist for martensitic stainless steel, which is difficult to passivate, as microscopic discontinuities can form in the surface of a machined part during passivation in a typical nitric acid bath.[8] The passivation process removes exogenous iron, creates/restores a passive oxide layer that prevents further oxidation (rust), and cleans the parts of dirt, scale, or other welding-generated compounds (e.g. oxides).[9][10]

Passivation processes are generally controlled by industry standards, the most prevalent among them today being ASTM A 967 and AMS 2700. These industry standards will generally list several typical "types" of passivation processes that can be used, with the specific method to be decided between the customer and vendor. The "Method" refers to either the use of a nitric acid-based passivating bath (Method 1), or a citric acid based bath (Method 2.) The various 'Types' found listed under each method refer to differences in acid bath temperature and concentration. Sodium dichromate is often required as an additive to promote oxidation in certain 'types' of nitric-based acid baths.


This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.