World Library  
Flag as Inappropriate
Email this Article

Piston Valve (steam Engine)

Article Id: WHEBN0012342390
Reproduction Date:

Title: Piston Valve (steam Engine)  
Author: World Heritage Encyclopedia
Language: English
Subject: Slide valve, Vauclain compound, Caprotti valve gear, Bulleid chain-driven valve gear, PRR E6
Publisher: World Heritage Encyclopedia

Piston Valve (steam Engine)

Diagram of cylinder and piston valve. The valve is next opened by moving it to the right, allowing the clear space in the middle of the valve to align with the channel in the cylinder above it.

Piston valves are one form of valve used to control the flow of steam within a steam engine or locomotive. They control the admission of steam into the cylinders and its subsequent exhausting, enabling a locomotive to move under its own power.


In the 19th century, steam locomotives used slide valves to control the flow of steam into and out of the cylinders. In the 20th century, slide valves were gradually superseded by piston valves, particularly in engines using superheated steam. There were two reasons for this:

  • It is difficult to lubricate slide valves adequately in the presence of superheated steam
  • With piston valves, the steam passages can be made shorter. This, particularly following the work of André Chapelon, reduces resistance to the flow of steam and improves efficiency

The usual locomotive valve gears such as Stephenson, Walschaerts, and Baker valve gear, can be used with either slide valves or piston valves. Where poppet valves are used, a different gear, such as Caprotti valve gear may be used, though standard gears as mentioned above were used as well, by Chapelon and others.


The Swannington incline winding engine of 1833 incorporated a piston valve

The Swannington incline winding engine on the Leicester and Swannington Railway, manufactured by The Horsely Coal & Iron Company in 1833, shows a very early use of the piston valve.[1] Piston valves had been used a year or two previously in the horizontal engines manufactured by Taylor & Martineau of London, but did not become general for stationary or locomotive engines until the end of the 19th century.[2]

Design principles

When on the move, a steam locomotive requires steam to enter the piston at a controlled rate.[3] This entails controlling the admission and exhaustion of steam to and from the cylinders.[3] Steam enters and leaves the valve through a steam port, usually at the middle position of the piston valve.[3] Where the valve is in contact with the steam ports, a consideration of the "lap" and "lead" is required.


The "Lap" is the amount by which the valve overlaps each steam port at the middle position of each valve.[3] However, there are two different types of "Lap."

The first kind is the "steam lap," which is the amount by which the valve overlaps the port on the live steam side of the cylinder.[3] Secondly, there is the "exhaust lap," which is the amount by which the valve overlaps the port on the exhaust side of the cylinder. "Exhaust lap" is generally given to slow-running locomotives.[3] This is because it allows the steam to remain in the cylinder for the longest possible amount of time before being expended as exhaust, therefore increasing efficiency.[3] shunter locomotives tended to be equipped with this addition.

The "Negative exhaust lap", also commonly termed "exhaust clearance," is the amount the port is open to exhaust when the valve is in mid-position, and this is used on many fast-running locomotives to give a free exhaust.[3] The amount seldom exceeds 1/16 in. when exhaust clearance is given; the cylinder on both sides of the piston is open to exhaust at the same time when the valve is passing through the mid-position, which is only momentary when running.[3]


The "lead" of the valve is the amount by which the steam port is open when the piston is static at front or back dead centre.[3] Pre-admission of steam fills the clearance space between the cylinder and piston and ensures maximum cylinder pressure at the commencement of the stroke.[3] "Lead" is particularly necessary on locomotives designed for high speeds, under which conditions the valve events are taking place in rapid succession.[3]

Valve travel

Long-travel piston valves allow the use of large steam ports to ease the flow of steam into, and out of, the cylinder.

Calculating valve events

Given the valve's lap, lead, and travel, at what point in the piston's stroke does the valve open and close, to steam and to exhaust?

Calculating an exact answer to that question before computers was too much work. The easy approximation (used in Zeuner's and Realeaux's diagrams) is to pretend that both the valve and the piston have a sine-wave motion (as they would, if the main rod were infinitely long). Then, for instance, to calculate the percent of the piston's stroke at which steam admission is cut off:

  • Calculate the angle whose cosine is twice the lap divided by the valve travel
  • Calculate the angle whose cosine is twice the (lap plus lead), divided by the valve travel

Add the two angles and take the cosine of their sum; subtract 1 from that cosine and multiply the result by -50.

As built the Pennsylvania's I1s 2-10-0 had lap 2 inches, lead 1/4 inch and valve travel 6 inches in full gear. In full gear the two angles are 48.19 deg and 41.41 deg and the maximum cutoff comes out 49.65% of the piston stroke.

See also


  1. ^ Clinker, C.R. (1977) The Leicester & Swannington Railway Bristol: Avon Anglia Publications & Services. Reprinted from the Transactions of the Leicestershire Archaeological Society Volume XXX, 1954.
  2. ^ Information plaque on the Swannington engine, National Railway Museum, York.
  3. ^ a b c d e f g h i j k l Garratt, C. & Wade-Matthews, M.: The Ultimate Encyclopedia of Steam & Rail (London: Hermes Publishing Company, Ltd., 1998) ISBN 1-84038-088-8
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.