World Library  
Flag as Inappropriate
Email this Article

Channel wing

Article Id: WHEBN0023580000
Reproduction Date:

Title: Channel wing  
Author: World Heritage Encyclopedia
Language: English
Subject: Aerodynamics, Aviation in Maryland, Gust lock, Wingbox, Passenger service unit
Publisher: World Heritage Encyclopedia

Channel wing

Channel Wing aircraft CCW-5

The channel wing is an aircraft wing principle developed by Willard Ray Custer in the 1920s. The most important part of the wing consists of a half-tube with an engine placed in the middle, driving a propeller placed at the rear end of the channel formed by the half-tube.

Antonov Izdeliye 181 Experimental


In 1925, Willard Custer had himself observed how very strong winds had managed to lift the roof of a barn. Custer realized it was the high velocity of the wind that created this suction, even when the barn itself was obviously not moving. He started studies into this phenomenon, and by 1928 he had made the first models of a wing with a half-tube-formed section instead of the usual wing profile. This was patented in 1929. Development of the half-tube channel wing was then refined further, and on November 12, 1942, the CCW-1 (Custer Channel Wing 1) airplane was flying for the first time. Custer built additional experimental aircraft; the last one was CCW-5, of which a few were manufactured in 1964.

Functional principle

Sketch of channel wing (seen from front)

Custer's summary of his invention was that the key to the lift created by a wing is the velocity of the stream of air passing over the wing, not the velocity of the airplane itself: It's the speed of air, not the airspeed!

A wing functions because the air over the wing has a lower pressure than the air under it. The conventional aircraft must reach a significant minimum speed before this pressure differential become large enough that it generates sufficient lift to become airborne.

In Custer's channel wing the rotating propeller will direct a stable stream of air backwards through the channel. A propeller will at the low pressure side normally be supplied by air from all directions. Since the half-tube prevents air from being drawn from below, the air will be sucked through the channel instead. This creates a strong low pressure area in the channel, which again generates a lift.

Applications and limitations

The layout was for a long time not successfully proven in an aircraft, even though Custer showed theoretically and experimentally that the principle was capable of vertical flight. Since they were built with conventional rudders needing some minimum airspeed to be functional, none of the aircraft designed by Custer were capable of full vertical takeoff, but instead were characterized as STOL (short takeoff and landing). The required runway for takeoff was very short, however, 200 feet (61 m) for the CCW-1, 66 feet (20 m) for the CCW-2, with a take off speed of as low as 20 miles per hour (32 km/h). Full vertical takeoff is theoretically feasible, but would require additional modifications and means of control.

Custer investigated both aircraft with pure channel wings as well as aircraft with additional conventional wings located outside the channels. The construction functions very well at relatively low speeds. At higher speeds, at high propeller RPM, oscillations would occur in the areas around the propeller, causing increased noise as well as creating long term destructive vibrations in the structure.

The twin engine layout featuring two channel wing features, was the most tested configuration. The twin layout had a higher risk of loss of control during a single engine failure situation, and required very high nose up attitude for STOL flight compared to conventional twin engine aircraft.[1]

Two of Custer's CCW aircraft survive. The CCW-1 is located at the Smithsonian´s National Air & Space Museum in Suitland, Maryland. The CCW-5, which was based on the Baumann Brigadier executive aircraft, is exhibited at the Mid-Atlantic Air Museum in Pennsylvania.

Later, research performed by NASA concluded that the advantage in lift and field length performance achieved did not offset the layout's many deficiencies in climb and high speed ability, and problems meeting certification requirements for general aviation.[2] The main issue is that the semi-circular beam wing configuration incurs increased profile drag and weight penalties over a conventional wing of the same lifting planform, and a common straight wing could provide almost the equivalent lift enhancement when exposed to the same slipstream induced increased dynamic pressure.

Hybrid Channel Wing

From 1999-2004 A joint research project led by Georgia Institute of the Technology Research Institute in Atlanta was funded by Langley Research Center. Aircraft were tested using channel wing principle layouts with circulation control devices that leveraged the Coandă effect. Performance of the wing was increased, and angle of attack was lowered, reducing some of the drawbacks of the design. The resultant design has been patented.[3]

Channel wing principle aircraft examples

Model Designer Company approximate year
CCW-1 Willard Ray Custer Custer Channel Wing Corporation 1942
CCW-2 Willard Ray Custer Custer Channel Wing Corporation 1948
CCW-5 Willard Ray Custer Custer Channel Wing Corporation 1953-64
RFV-1 Hanno Fischer Rhein-Flugzeugbau, Mönchengladbach 1960
P-20 Raider Product Development Group 1985
P-50 Devastator Product Development Group 1986
Modified V-22 Osprey not finished Product Development Group 1988
Izdelie 181 Oleg K. Antonov Antonov 1990


  1. ^ "That little extra lift". Air and Space. April 2007. 
  2. ^ The Channelwing Revisited, Harry Clements, SAE Document Number: 2006-01-2387
  3. ^ "That little extra lift". Air and Space. April 2007. 
  • Donald Liska - Channelwing aircraft, The Wisconsin engineer Vol. 57, Nr. 6, pp 16 –19, October 1957, [1]
  • Kevin Brown - Cockpit-Testing the Legendary Channel-Wing, Popular Mechanics, September 1964
  • Robert Englar, Brian Campbell - Development of Pneumatic Channel Wing Powered-Lift Advanced Super-STOL Aircraft, 1st Flow Control Conference 24–26 June 2002, AIAA 2002-3275, St. Luis, Missouri, 2002
  • Walt Boyne - The Custer Channel Wing Story, Airpower Magazine, Volume 7 No.3 May 1977
  • Unknown author - Custer's Production Model Takes Bow, Air Progress Magazine, October/November, 1964
  • Unknown author - Channel Wing Flown in Demonstration, Aviation Week, September 28, 1959

External links

  • Custer-Channelwing Website Archive
  • Another Custer Channel Wing Website
  • Video of Custer explaining his theories and actual flight footage
  • Pictures of the Custer CCW-1 National Air and Space Museum
  • Pictures of the Custer CCW-5 Mid-Atlantic Air Museum, Reading, Pennsylvania
  • Modern channelwing aircraft design Stavatti designed channelwing transport for the 2000s
This article was sourced from Creative Commons Attribution-ShareAlike License; additional terms may apply. World Heritage Encyclopedia content is assembled from numerous content providers, Open Access Publishing, and in compliance with The Fair Access to Science and Technology Research Act (FASTR), Wikimedia Foundation, Inc., Public Library of Science, The Encyclopedia of Life, Open Book Publishers (OBP), PubMed, U.S. National Library of Medicine, National Center for Biotechnology Information, U.S. National Library of Medicine, National Institutes of Health (NIH), U.S. Department of Health & Human Services, and, which sources content from all federal, state, local, tribal, and territorial government publication portals (.gov, .mil, .edu). Funding for and content contributors is made possible from the U.S. Congress, E-Government Act of 2002.
Crowd sourced content that is contributed to World Heritage Encyclopedia is peer reviewed and edited by our editorial staff to ensure quality scholarly research articles.
By using this site, you agree to the Terms of Use and Privacy Policy. World Heritage Encyclopedia™ is a registered trademark of the World Public Library Association, a non-profit organization.

Copyright © World Library Foundation. All rights reserved. eBooks from Project Gutenberg are sponsored by the World Library Foundation,
a 501c(4) Member's Support Non-Profit Organization, and is NOT affiliated with any governmental agency or department.